All documents are in PDF format. Use the freely available Adobe Acrobat Reader to view them.   

Design & Construction Standards (complete file | 4.49MB) contains the following: 

• Section 01 - Administrative [560 KB]
• Section 02 - Water/Sewer Standards [293 KB]
• Section 03 - Specifications [928 KB]
• Section 04 - Water Detail Drawings [1.32 MB]
• Section 05 - Sewer Detail Drawings [1.28 MB] 

Individual Downloads 
Section 01 - Administrative

• Water/Sewer Availability Application
  
• Sizing Water Service Lines and Meters
  
• Water Meter Fixture Value Chart
• Non-Residential Sanitary Sewer Checklist
  
• Plan Submittal Checklist
  
• Request for Waiver, Modification or Field Change Form
  
• Inspection Requirements
  
• Acceptance of Water/Sewer Facilities Procedures
  
• Typical Water or Sewer Main Location Within VDOT Right-of-Ways
   

Section 02 - Water/Sewer Standards

• Design and Construction Standards for Water Facilities - Section 100.00
• Design and Construction Standards for Sanitary Sewer Facilities - Section 200.00 

Section 03 - Specifications

• Specification Section 02110 - Clearning and Grubbing
• Specification Section 02230 - Rock Excavation
• Specification Section 02270 - Erosion and Sediment Control
• Specification Section 02310 - Stream and/or Highway Crossings
• Specification Section 02665 - Water Distribution Lines
• Specification Section 02670 - Installation of Water Lines and Sanitary Sewer Lines by Horizontal Directional Drilling (HDD) Method
• Specification Section 02731 - Sanitary Sewer Collection Lines and Force Main
• Specification Section 02900 - Seeding and Mulching 

Section 04 - List of Water Detail Drawings

• W-01 - Single Residential Water Service
• W-02 - Single Residential Service for High Pressure
• W-03 - Single Residential Service with PRV
• W-04 - Commercial Water Service
• W-05 - Double Residential Water Service
• W-06 - Typical Sewer Subtraction Meter Configuration
• W-07 - Sewer Subtraction Meter Installation
• W-08 - Water Line Valve Installation
• W-09 - Permanent End of Line
• W-10 - Blow-Off Assembly for Main Line Temporary Termination
• W-11 - In-Line Blow-Off Assembly
• W-12 - Automatic Air Release Assembly
• W-13 - Automatic Air Release Assembly for Deep Water Line
• W-14 - Main Line Pressure-Reducing Valve Assembly
• W-15 - Alternate Valve Vault (Manhole)
• W-16 - Installation Detail for All Frames and Covers
• W-17 - Manhole Frame and Cover
• W-18 - Fire Hydrant Assembly
• W-19 - Thrust Block Construction
• W-20 - Thrust Restraint of Pipe Joints Design Lengths
• W-21 - Typical Water Pressure Test Rig
• W-22 - Pipe Support in Casing Pipe 

Section 04 - List of Sewer Detail Drawings

• S-01 - 4' Standard Manhole for Pipe 15" or Smaller
• S-02 - Straddle Manole for Pipe 15" or Smaller
• S-03 - Outside Drop Manhole (For use with PVC pipe)
• S-04 - Mainline or lateral Inside Drop Manhole (For use with PVC pipe)
• S-05 - Watertight Manhole Frame and Cover
• S-06 - Sampling Structure
• S-07 - Sanitary Sewer Lateral
• S-08 - Sanitary Sewer Lateral for Deep Sewers
• S-09 - Sanitary Sewer Lateral for Special Cases
• S-10 - Combined 6" by Two 4" Laterals
• S-11 - Force Main to Gravity Lateral Conn.
• S-12 - PVC - Force Main Cleanout
• S-13 - Traffic Bearing Cleanout Box
• S-14 - Alternate Traffic Bearing Cleanout Box
• S-15 - Stone Bedding
• S-16 - Concrete Encased Pipe
• S-17 - Joining Dissimilar Pipe
• S-18 - Concrete Pier
• S-19 - Anchor Block
• S-20 - Pipe Support in Casing Pipe
• S-21 - Type 1 Manhole Vent - Out of Right of Way
• S-22 - Type 2 Manhole Vent
• S-23 - Automatic Air Release Assembly for use on Sewer Force Main
• S-24 - Pavement Replacement - Open Cut Roadway
• S-25 - Sanitary Sewer Abandonment at a Manhole
• S-26 - Sanitary Sewer Manhole Abandonment
• S-27 - Sanitary Sewer Easements
• S-28 - Chain Link Fence
• S-29 - Air Testing Back Pressure Equivalency Table
• S-30 - Air Testing Time for 1 PSI Drop
• S-31 - Air Testing Time for 0.5 PSI Drop